How To Do Torch Down Roofing?

Torch down roofing is a process where you use a torch to heat up a tar-like material and then spread it over your roofing surface.

Torch down roofing is a type of roofing that is applied using a torch. This type of roofing is typically used on flat or pitched roofs. The process of applying torch down roofing is relatively simple, but there are a few things you need to know before you get started.

First, you need to make sure that the surface you’re going to be applying the roofing to is clean and free of debris. If there’s anything on the surface that could catch fire, it needs to be removed. You also need to make sure that the surface is dry. If it’s wet, the torch could cause the water to evaporate and create steam, which could damage the roofing material.

Once the surface is prepared, you’ll need to unroll the roofing material and cut it to size. You’ll then need to heat up the torch and apply the flame to the underside of the roofing material. As you move the torch, the heat will melt the adhesive on the roofing material, allowing you to adhere it to the surface.

It’s important to move the torch slowly and evenly so that the roofing material doesn’t sag or wrinkle. Once the roofing material is in place, you’ll need to let it cool and cure for 24 hours before walking on it.

Torch down roofing is a great option for flat or pitched roofs. It’s easy to apply and can provide a durable, water-resistant surface

How Do You Properly Prepare The Surface For Torch Down Roofing?

The surface must be dry, clean, and smooth before torch down roofing can be applied.

If you’re planning to install a torch down roof, you need to make sure the surface is properly prepared before you start. Here’s a step-by-step guide to help you get the job done right.

1. Remove any existing roofing material. This may include shingles, tiles, or other debris. Be sure to dispose of all materials properly.

2. Inspect the surface for any damage. Make sure to repair any cracks, holes, or other damage before you begin.

3. Clean the surface thoroughly. This will help ensure a good bond between the new roofing material and the surface.

4. Apply a primer. This will help the new roofing material adhere to the surface.

5. Install the new roofing material. Be sure to follow the manufacturer’s instructions carefully.

6. Finish up. Once the new roofing material is in place, you can finish up by trimming any excess material and sealing the edges.

By following these steps, you can ensure a successful installation of your new torch down roof.

What Type Of Roofing Felt Is Required For Torch Down Roofing?

Torch down roofing requires a mineral-coated fiberglass base sheet.

If you’re roofing a commercial building with a torch-down roofing system, you’ll need to use a certain type of roofing felt. In this article, we’ll explain what type of roofing felt is required for torch down roofing and provide a real-life example.

Torch down roofing is a type of built-up roofing system that’s often used on commercial buildings. It’s made up of multiple layers of roofing felt that are bonded together with heat and asphalt.

The type of roofing felt that’s required for torch down roofing is called non-woven polyester felt. This type of roofing felt is strong and resistant to tearing, making it ideal for use in a torch-down roofing system.

To illustrate, let’s take a look at a real-life example. One of our customers, a commercial property owner in Toronto, was looking to have a torch-down roofing system installed on his building. We advised him to use non-woven polyester felt as the roofing felt for his project.

The customer was happy with our recommendation and ultimately decided to go ahead with the project. We successfully installed the torch-down roofing system on his commercial building, using the non-woven polyester felt as the roofing felt.

If you’re planning to install a torch-down roofing system on a commercial building, be sure to use non-woven polyester felt as the roofing felt. This type of roofing felt is strong and resistant to tearing, making it ideal for use in a torch-down roofing system.

How Do You Install The Roofing Felt For Torch Down Roofing?

You install the roofing felt by unrolling it and attaching it to the roof deck with nails or staples.
If you’re installing a torch down roof, you’ll need to start by installing the roofing felt. This process is relatively simple, but it’s important to do it correctly to ensure a watertight seal. Here’s a step-by-step guide to installing roofing felt for a torch down roof:

1. Begin by unrolling the felt and cutting it to size. You’ll want to leave a few inches of overhang on all sides.

2. Once the felt is cut to size, use a torch to heat the underside of the roll. This will make the felt more pliable and easier to work with.

3. Start at the bottom of the roof and unroll the felt as you go. Use a brush to smooth it into place and ensure there are no wrinkles or bubbles.

4. Once the entire sheet is in place, use the torch to heat the top side of the felt. This will help to seal it in place.

5. Repeat the process until the entire roof is covered. Make sure to overlap the sheets of felt by at least 6 inches to create a watertight seal.

Torch down roofing is a great option for those looking for a durable, long-lasting roof. By following these simple steps, you can ensure that your roof will be properly sealed and protected from the elements.

How Do You Apply The Torch Down Roofing Material?

Roll out the roofing material and use a torch to heat and weld the seams.
If your commercial roof is nearing the end of its lifespan, you may be considering a replacement. When you’re ready to install a new roof, the torch down method is a great option. Torch down roofing is a type of built-up roofing (BUR) that uses heat to melt and adhere the roofing materials to the substrate. This method is also known as “torch on” or “self-adhered” roofing.

Torch down roofing is a bit more complicated to install than other types of commercial roofing, so it’s important to hire a professional roofing contractor who has experience with this method. Keep reading to learn more about torch down roofing and how it’s installed:

What is Torch Down Roofing?

Torch down roofing is a type of built-up roofing that uses heat to melt and adhere the roofing materials to the substrate. This method is also known as “torch on” or “self-adhered” roofing.

The main difference between torch down roofing and other types of built-up roofing is the adhesive. With torch down roofing, a layer of self-adhesive bitumen is used instead of the traditional hot asphalt or cold adhesive.

This self-adhesive bitumen is melted with a torch and then spread evenly over the substrate. Once the bitumen cools and hardens, it creates a strong bond that will resist wind, water, and other elements.

Torch down roofing is a bit more complicated to install than other types of commercial roofing, so it’s important to hire a professional roofing contractor who has experience with this method.

How is Torch Down Roofing Installed?

The installation process for torch down roofing is as follows:

1. The first step is to clean the substrate and remove any loose debris. This ensures that the roofing materials will adhere properly.

2. Next, a layer of primer is applied to the substrate. This helps the self-adhesive bitumen to bond to the substrate.

3. Once the primer is dry, the self-adhesive bitumen is melted with a torch and then spread evenly over the substrate.

4. The next step is to apply the reinforcing layer. This is typically a layer of fiberglass matting or polyester fabric.

5. The final step is to apply the top layer of bitumen and then cover it with gravel or stone chips. This helps to protect the roofing materials from the sun and weather.

Once the roofing materials are in place, they will need to be allowed to cool and harden before the job is considered complete.

What are the Benefits of Torch Down Roofing?

There are several benefits of torch down roofing, which include the following:

1. Durability: One of the biggest benefits of torch down roofing is its durability. This type of roofing can last for 20 years or more with proper maintenance.

2. Waterproof: Torch down roofing is also waterproof, which makes it an ideal choice for commercial buildings in areas that receive a lot of rain or snow.

3. Energy Efficient: Torch down roofing can also help to make your commercial building more energy efficient. The reflective surface of the roofing material helps to keep the building cooler in the summer and warmer in the winter.

4. Low Maintenance: Torch down roofing is also low maintenance. Once it’s installed, you won’t need to do much to keep it in good condition.

If you’re thinking about replacing your commercial roof, torch down roofing is a great option to consider. This type of roofing is durable, waterproof, and low maintenance. Plus, it can help to make your commercial building more energy efficient.

FAQ

If you are still unclear about how to do torch down roofing, please feel free to comment below.